How to Sublimate a 30 oz Tumbler
A 30 oz tumbler is the same idea as a 20 oz, just bigger. But that extra size changes three things: the paper you print on, the shrink wrap you use, and whether your press can fit it at all. Here's how to sublimate one without wasting a blank.
By the CraftSizer team · Updated 2026-11-11

30 oz template size
| Tumbler | Typical template | Pixels at 300 DPI |
|---|---|---|
| 20 oz skinny straight | about 9.3 × 8.2 in | 2790 × 2460 |
| 30 oz skinny straight | about 9.77 × 9.5 in | 2931 × 2850 |
Typical sizes including a small seam overlap. 30 oz tumblers vary more than most, so measure yours.
To measure: wrap a strip of paper around the tumbler for the circumference, then measure the straight height you can print on. The tumbler template calculator adds the seam overlap and downloads a 300 DPI template at the exact size. Full guide: how to measure a tumbler.
Is yours tapered? Many 30 oz tumblers, especially "tapered" or "fatty" styles, are wider at the top than the bottom. A straight rectangle won't line up on those; use the tapered tumbler template generator instead.
Paper: you'll need tabloid
A 30 oz wrap is about 9.5 inches tall, which is more than the 8.5-inch side of letter paper. So it doesn't fit on letter even turned sideways. Most crafters print it on tabloid (11 × 17 in) paper, which needs a wide-format sublimation printer, or on a roll. See the sublimation paper size guide for what fits where.
If your printer only takes letter, some crafters split the design into two halves and line them up on the tumbler. It's fiddly and the join can show, so it's best for designs with a natural break.
Pressing a 30 oz tumbler
| Method | Temperature | Time |
|---|---|---|
| Convection oven + shrink wrap | 375–400 °F (191–204 °C) | about 5–8 min |
| Tumbler press | 350–375 °F (177–191 °C) | about 90 sec – 3 min |
Common starting points. Larger tumblers often need the upper end of the time range. Your blank's instructions come first.
- Shrink wrap: use sleeves sized for 30 oz tumblers. A 20 oz sleeve may not shrink evenly over the larger cup.
- Tumbler press: many presses are made for 20 oz skinny tumblers. Check that the heating element is tall enough to cover the full 9.5-inch wrap, or the top or bottom will come out pale.
- Turn it in the oven halfway through if your oven heats unevenly.
Choosing between the two? See shrink wrap vs tumbler press, and the full sublimation time and temperature chart.
Step by step
- Measure the tumbler and make the template at the exact size.
- Print mirrored on tabloid sublimation paper, at about 300 DPI.
- Wrap the print tightly, seam at the back or under the handle area, and tape it down so it can't move.
- Slide on a 30 oz shrink wrap sleeve and shrink it with a heat gun, or load the tumbler into the press.
- Press, then remove the wrap and paper right away (wearing gloves) and let it cool.
Common 30 oz problems
- White line at the seam: the template is a little too narrow. Re-measure and add about 0.1 inch.
- Pale band at the top or bottom: the press element doesn't cover the whole wrap, or the shrink wrap is loose there.
- Design runs onto the curve: the template is taller than the straight part. Measure only the flat area.
Frequently asked questions
What size is a 30 oz skinny tumbler sublimation template?
About 9.77 × 9.5 inches, or 2931 × 2850 pixels at 300 DPI, including a small seam overlap. Measure your tumbler, since 30 oz tumblers vary between brands.
Can you print a 30 oz tumbler wrap on letter paper?
Usually not. At about 9.5 inches tall, the wrap is taller than the 8.5-inch side of letter paper, so most crafters print it on 11 × 17 tabloid paper.
How long do you sublimate a 30 oz tumbler in the oven?
About 5 to 8 minutes at 375 to 400 °F with shrink wrap, often toward the longer end for bigger tumblers. Follow your blank's instructions first.
Will a 30 oz tumbler fit in my tumbler press?
Not always. Many tumbler presses are sized for 20 oz skinny tumblers, so check that the heating element covers the full height of a 30 oz wrap.