Home › Blog › How to Sublimate Coasters

How to Sublimate Coasters

Coasters are one of the easiest sublimation blanks to sell in sets, but there are several kinds, and each presses differently. A neoprene coaster takes under a minute; a ceramic or sandstone one takes several. Here's how to press each type.

By the CraftSizer team · Updated 2026-11-18

Sublimation coaster settings: neoprene 380 to 400 degrees 40 to 60 seconds, MDF 390 to 400 degrees 60 to 75 seconds, ceramic 385 to 400 degrees 3 to 5 minutes, sandstone 390 to 400 degrees 4.5 to 5.5 minutes
Starting settings for each type of coaster.

Settings by coaster type

CoasterTemperatureTimePressure
Neoprene / fabric top380–400 °F (193–204 °C)40–60 secLight–medium
MDF / hardboard390–400 °F (199–204 °C)60–75 secMedium
Ceramic385–400 °F (196–204 °C)3–5 minMedium
Sandstone / car coaster390–400 °F (199–204 °C)4.5–5.5 minLight

Common starting points. Your blank's instructions come first, especially for ceramic and sandstone. Full chart for 21 blanks: sublimation time and temperature chart.

Design size

Most square coasters are about 3.5–4 inches, and round ones about 3.5–4 inches across. Measure yours and make the design about 1/8 inch bigger on each side (bleed), so there's no white edge. At 300 DPI, a 4-inch coaster design is 1200 pixels across; check yours with the DPI checker.

Step by step

  1. Remove any protective film from MDF or ceramic blanks.
  2. Print mirrored on the bright side of the paper. You can fit several coasters on one letter sheet.
  3. Tape the print to the coaster. For hard coasters, place the blank face down on the print.
  4. Press with butcher paper above and below. For hard coasters, many crafters put the print on the bottom and the blank on top, so the paper stays flat against the coating.
  5. Peel the paper while hot, and let the coaster cool on a flat, heat-safe surface. Ceramic and sandstone stay hot for a long time.

Tips by type

Common problems

ProblemTry
Unprinted corners or edges on ceramicMore even pressure: add a felt pad, center the coaster under the press
White borderAdd bleed around the design
Dull print on MDFRemove the film; add 10 seconds
Blurry edgesTape firmly and peel straight away

Selling coaster sets? Work out a fair price with the craft pricing calculator.

Frequently asked questions

How long do you sublimate a ceramic coaster?

About 3 to 5 minutes at 385 to 400 °F with medium pressure is a common starting point. Follow your blank's instructions first.

What temperature do you sublimate neoprene coasters?

About 380 to 400 °F for 40 to 60 seconds with light to medium pressure.

How do you sublimate sandstone coasters?

Usually 390 to 400 °F for about 4.5 to 5.5 minutes with light pressure. Too much pressure can crack sandstone.

What size should a coaster design be?

Measure your coaster and add about 1/8 inch on each side. Most square coasters are about 3.5 to 4 inches.

Free tools for this

Free tool

Sublimation Time & Temperature Chart

Starting heat, time and pressure for shirts, mugs, tumblers and more, with a built-in press timer.

Free tool

Sublimation DPI & Print Size Calculator

Convert pixels to inches, find the pixels you need, and check if an image is sharp enough to print.

Free tool

Craft Pricing Calculator

Price handmade items three ways: cost-plus, the wholesale × 2 formula, and profit after Etsy-style fees.

More articles